Dfi COM330-B Manual de usuario Pagina 1

COM330-BSystem BoardUser’s ManualA21110401

110IntroductionCOM ExpressModulesDamage FreeIntelligenceROM InterfaceTemperatureHumidityPower OutputCertificationPCB• Basic• Compact• Legacy Super I/O

112Hardware InstallationSystem Board LayoutChapter 2 - Hardware InstallationBuzzer403912LVDS LCD panelSATA 1SATA 011SATA 2SATA 311SPI Flash BIOSBackli

122Hardware Installation1ON451ON45JP1 is used to select the power of the PS/2 keyboard/mouse port. Selecting 5V_standby will allow you to use the PS/2

132Hardware Installation1ON451ON45JP2 (for USB 0-3) and JP4 (for USB 4-7) are used to select the power of the USB ports. Selecting 5V_standby will all

142Hardware Installation1ON451ON45Panel Power SelectJP11 is used to select the power supplied to the LCD panel.Important:Before powering-on the system

152Hardware InstallationJP15 is used to select the power supplied to the CF card that is on the motherboard. Selecting 3V3 will be the default setting

162Hardware Installation1ON451ON45Backlight Power SelectJP121 2 31 2 32-3 On: +3.3V(default)1-2 On: +5V JP12 is used to select the backlight contr

172Hardware Installation1ON451ON45Clear CMOS JP102-3 On: Clear CMOS1-2 On: Normal(default) 312312If you encounter the following,a) CMOS data becomes

182Hardware InstallationSuper IO Enable/ Disable3123122-3 On: Disable (default)1-2 On: Enable1ON451ON45JP3JP3 is used to select enable or disable the

192Hardware Installation1ON451ON45VCC5_IN Power SelectJP91-2 On: 5VSB (default)JP9 is used to select the power of the COM Express connector.6425316425

CopyrightThis publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to

202Hardware Installation1ON451ON45PCIe x16 Normal/ ReversedJP71 2 32-3 On: Reversed(for cards that support reversed signals)1-2 On: Normal (defaul

212Hardware Installation1ON451ON45BIOS SelectJP5 and JP6 are used to determine the BIOS boot device.312JP6: 1-2 OnJP5: 1-2 OnCarrier LPC FWHModule SPI

222Hardware Installation1ON451ON45FWH Write ProtectJ131-2 Off: Disable (Default)1-2 On: Enable 2121J13 is used to confi gure the BIOS Write Protect fu

232Hardware InstallationFunction Test JumpersBattery Low Test1ON451ON45This jumper is used to simulate the signal status that indicates the external

242Hardware InstallationWake-up Test1ON451ON45This jumper is used to simulate the signal status that indicates the wake-on-ring or PME# event from the

252Hardware InstallationThermal Trigger1ON451ON45This jumper is used to simulate the signal status that indicates the Over Temper-ature Signal (OVT) o

262Hardware InstallationRear Panel I/O PortsThe rear panel I/O ports consist of the following:• PS/2 keyboard port• PS/2 mouse port• 3 COM ports

272Hardware Installation1ON451ON45PS/2 Mouse and Keyboard PortPS/2 Mouseand keyboard (option)These ports are used to connect a PS/2 mouse and

282Hardware Installation1ON451ON45COM 3COM 1Serial (COM) PortsCOM 2192DCD-TDRDDTR-GNDRTS-DSR-CTS-RI-The system board is equipped with 3 onboard

292Hardware Installation1ON451ON45The VGA port is used for connecting a VGA monitor. Connect the monitor’s 15-pin D-shell cable connector to the

FCC and DOC Statement on Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 o

302Hardware Installation1ON451ON45RJ45 LAN PortThe onboard RJ45 LAN port allows the system board to connect to a local area network by m

312Hardware Installation1ON451ON45Universal Serial Bus ConnectorsUSB 2-3USB 0-1USB allows data exchange between your computer and a wide ran

322Hardware InstallationWake-On-USB Keyboard/MouseThe Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse to wake up a

332Hardware Installation1ON451ON45Audio Front audioRear audioRear AudioThe system board is equipped with 3 audio jacks. A jack is a one-hole connectin

342Hardware Installation1ON451ON45S/PDIF ConnectorThe S/PDIF connector is used to connect external S/PDIF ports. Your S/PDIF ports may be

352Hardware Installation1ON451ON45LVDS LCD Panel ConnectorLCD/Inverter Power ConnectorThe system board allows you to connect a LCD Display P

362Hardware InstallationPins13579111315171921232527293133353739FunctionGNDLVDS_Out3+LVDS_Out3-GNDLVDS_Out2+LVDS_Out2-GNDLVDS_Out1+LVDS_Out1-GNDLVDS_Ou

372Hardware Installation1ON451ON45Digital I/O Connector2119DIOThe 8-bit Digital I/O connector provides powering-on function to external devices that a

382Hardware Installation1ON451ON45LPC connectorThe Low Pin Count Interface was dened by Intel® Corporation to facilitate the in-dustry’s transition

392Hardware Installation1ON451ON45SATA (Serial ATA) Connectors7RXNGNDTXPTXNGND1RXPGNDSATA 2.0 3Gb/sSATA 2SATA 3SATA 1SATA 0SATA 3.0 6Gb/sThe Serial

Table of ContentsCopyright ...2Trademarks ...

402Hardware Installation1ON451ON45Cooling Fan ConnectorsThe fan connectors are used to connect cooling fans. The cooling fans will pro-vi

412Hardware InstallationI2C Connector1ON451ON4514I2C_DAT3V332I2C_CLKGroundThe 1-channel I2C bus interface conforms to the version 2.1 I2C bus specica

422Hardware Installation1ON451ON45SM busThe SMBus (System Management Bus) connector is used to connect SMBus devices. It is a multiple device bus that

432Hardware Installation1ON451ON45Power ConnectorsImportantThe system board consumes a minimal amount of power. Due to its low power consu

442Hardware Installation1ON451ON45Standby Power LEDStandby Power LEDThis LED will lit red when the system is in the standby mode. It ind

452Hardware Installation1ON451ON45Front Panel ConnectorsHDD-LED - HDD LEDThis LED will light when the hard drive is being accessed.RESET SW - Reset Sw

462Hardware Installation1ON451ON45Expansion SlotsPCI Express x16 SlotInstall PCI Express x16 graphics card, that comply to the PCI Express

472Hardware InstallationSwitches1ON451ON45PowerReset

482Hardware InstallationCompactFlash Socket1ON451ON45CompactFlash SocketThe CompactFlashTM socket is used for inserting a CompactFlashTM card. Compact

492Hardware Installation1ON451ON45Chassis Intrusion Connector The board supports the chassis intrusion detection function. Connect the chas-sis intrus

Audio ... 33Internal I/O Connectors ...

502Hardware Installation1ON451ON45The lithium ion battery powers the real-time clock and CMOS memory. It is an auxiliary source of power when the main

512Hardware InstallationCOM Express ConnectorsThe COM Express connectors are used to interface the carrier board with a COM Express board. Refer to th

522Hardware Installation

532Hardware Installation

542Hardware Installation

55Supported Software3The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance

56Supported Software3Audio DriversTo install the driver, click “Audio Drivers” on the main menu.1. Setup is now ready to in-stall the audio driver. C

57Supported Software3Adobe Acrobat Reader 9.3To install the reader, click “Adobe Acrobat Reader 9.3” on the main menu.1. Click Next to install or cli

16IntroductionAbout this ManualAn electronic file of this manual is included in the CD. To view the user’s manual in the CD, insert the CD into a CD-R

17IntroductionStatic Electricity PrecautionsIt is quite easy to inadvertently damage your PC, system board, components or devices even before installi

18IntroductionAbout the PackageThe system board package contains the following items. If any of these items are missing or damaged, please contact you

19IntroductionChapter 1 - IntroductionSpecificationsAudioStorageDigital I/ORear Panel I/OPortsI/O ConnectorsExpension Slots• Realtek ALC886 5.1-channe