Dfi KB968 Manual de usuario descargar pdf (Pagina 24)

www.dﬁ .comChapter 3 Hardware Installation

Chapter 3

Signal Pin# Pin Type Pwr Rail /Tolerance KB968 Carrier Board Description

I2C_CK B33 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB General purpose I2C port clock output

I2C_DAT B34 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB General purpose I2C port data I/O line

SPKR B32 O CMOS 3.3V / 3.3V

Output for audio enunciator - the "speaker" in PC-AT systems.

This port provides the PC beep signal and is mostly intended for

debugging purposes.

WDT B27 O CMO

3.3V

3.3V Out

ut indicatin

that a watchdo

time-out event has occurred.

FAN_PWNOUT B101 O CMOS 3.3V / 12V PD 100K to GND Do NOT PU Fan speed control. Uses the Pulse Width Modulation (PWM) technique to control the fan's RPM.

FAN_TACHIN B102 I OD CMOS 3.3V / 12V PU 10K to 3.3V Fan tachometer input for a fan with a two pulse output.

TPM_PP A96 I CMOS 3.3V / 3.3V

Trusted Platform Module (TPM) Physical Presence pin. Active high.

TPM chip has an internal pull down. This signal is used to indicate

Physical Presence to the TPM.

Signal Pin# Pin Type Pwr Rail /Tolerance KB968 Carrier Board Description

PWRBTN# B12 I CMOS 3.3V Suspend/3.3V PU 10K to 3.3VSB

A falling edge creates a power button event. Power button events can

be used to bring a system out of S5 soft off and other suspend states,

as well as powering the system down.

SYS_RESET# B49 I CMOS 3.3V Suspend/3.3V PU 40-50K to 3.3VSB

Reset button input. Active low request for Module to reset and reboot.

May be falling edge sensitive. For situations when SYS_RESET# is

not able to reestablish control of the system, PWR_OK or a power

cycle may be used.

CB_RESET# B50 O CMOS 3.3V Suspend/3.3V PD 100K to GND

Reset output from Module to Carrier Board. Active low. Issued by

Module chipset and may result from a low SYS_RESET# input, a low

PWR_OK input, a VCC_12V power input that falls below the minimum

specification, a watchdog timeout, or may be initiated by the Module

software.

PWR_OK B24 I CMOS 3.3V / 3.3V PU 10K to 3.3V

Power OK from main power supply. A high value indicates that the

power is good. This signal can be used to hold off Module startup to

allow Carrier based FPGAs or other configurable devices time to be

programmed.

SUS_STAT# B18 O CMOS 3.3V Suspend/3.3V Indicates imminent suspend operation; used to notify LPC devices.

SUS_S3# A15 O CMOS 3.3V Suspend/3.3V

Indicates system is in Suspend to RAM state. Active low output. An

inverted copy of SUS_S3# on the Carrier Board may be used to

enable the non-standby power on a typical ATX supply.

SUS_S4# A18 O CMOS 3.3V Suspend/3.3V Indicates system is in Suspend to Disk state. Active low output.

SUS_S5# A24 O CMOS 3.3V Suspend/3.3V Indicates system is in Soft Off state.

WAKE0# B66 I CMOS 3.3V Suspend/3.3V PU 10K to 3.3VSB PCI Express wake up signal.

WAKE1# B67 I CMOS 3.3V Suspend/3.3V PU 40-50K to 3.3VSB

General purpose wake up signal. May be used to implement wake-up

on PS2 keyboard or mouse activity.

BATLOW# A27 I CMOS 3.3V Suspend/ 3.3V PU 10K to 3.3VSB

Indicates that external battery is low.

This port provides a battery-low signal to the Module for orderly

transitioning to power saving or power cut-off ACPI modes.

LID# A103 I OD CMOS 3.3V Suspend/12V LID switch. Low active signal used by the ACPI operating system for a LID switch.

SLEEP# B103 I OD CMOS 3.3V Suspend/12V PU 10K to 3.3VSB

Sleep button. Low active signal used by the ACPI operating system to bring the

system to sleep state or to wake it up again.

THRM# B35 I CMOS 3.3V / 3.3V PU 10K to 3.3V Input from off-Module temp sensor indicating an over-temp situation.

THRMTRIP# A35 O CMOS 3.3V / 3.3V PU 10K to 3.3V NA Active low output indicating that the CPU has entered thermal shutdown.

SMB_CK B13 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB System Management Bus bidirectional clock line.

SMB_DAT B14 I/O OD CMOS 3.3V Suspend/3.3V PU 2.2K to 3.3VSB System Management Bus bidirectional data line.

SMB_ALERT# B15 I CMOS 3.3V Suspend/3.3V

System Management Bus Alert – active low input can be used to

generate an SMI# (System Management Interrupt) or to wake the system.

Power and S

stem Mana

ement Si

nals Descri

tions

Miscellaneous Si

nal Descri

tions

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 67 68

Comentarios a estos manuales

Sin comentarios

Dfi KB968 Manual de usuario Pagina 24

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Dfi KB968